November 13, 2026 · Stainless Steel

How to Buy Stainless Steel Plate from China: Containers, Payment Terms and Inspection

Most buyers who buy stainless steel plate from China argue about the price per tonne and stop there. The two things that decide whether the container lands clean are loading and payment terms. A 20ft box takes 22 to 25 tonnes of 304 sheet. A 40ft takes 26 to 28. Below that sits the paperwork, and the paperwork is what a claim is settled on two years later.

How many tonnes of stainless steel plate fit in a container?

Plate is weight limited, not volume limited. That one sentence explains most of the confusion about container capacity.

ContainerInternal sizeUsable volumePractical plate load
20ft GP5,898 x 2,352 x 2,393 mm24-26 m³22-25 t
40ft GP12,032 x 2,352 x 2,393 mm54 m³26-28 t
40ft HC12,032 x 2,352 x 2,698 mm68 m³26-28 t

Stainless steel weighs 7.93 tonnes per cubic metre. One square metre of 1.0 mm sheet is 7.93 kg. Twenty five tonnes of 1.0 mm sheet in 1219 x 2438 mm therefore works out to roughly 1,060 sheets, and that stack is only about 1.1 metres tall. You are nowhere near the roof of the container.

Now run the same 25 tonnes in 6 mm plate and you get about 175 sheets, still less than a metre of stack. The weight arrives first every time. That is why nobody ships stainless plate in a 40ft HC for the extra height. You pay for the same 26 to 28 tonnes and the extra cubic metres go to waste.

The limit that catches people is the road, not the box

A 20ft container is rated around 28 tonnes payload. On European roads the axle limits usually pull that down to 24 tonnes, and in some countries lower. If your consignee is inland, ask the forwarder what the legal payload is on the final leg before you book 25 tonnes.

I have seen a buyer sit on a quay for four days because the truck could not legally leave with the box. Nobody warns you about that part.

What does a container of 304 plate cost in 2026?

Ex-China stainless prices split in early November 2026. Indonesian 304/2B FOB averaged about US$2,118 per tonne in the week of November 2 to 6, and 316L/2B about US$4,218. Both were up US$5 week on week, and that came from cost, not demand.

Nickel rallied after the US midterm results, and Jakarta signalled it wants to rein in ore output. Nickel pig iron posted its first weekly rise in twelve weeks. Meanwhile CIF Belgium was cut US$100 per tonne in a single move and Malaysian offers slipped about US$27. Ex-China is not one price. It is several, moving in different directions.

So the arithmetic on a 24 tonne 304/2B load at US$2,150 per tonne is US$51,600 of material. Freight, duty, insurance and inland haulage sit on top. If your supplier quotes you a number far under US$2,100 for 304 2B right now, ask which grade and which finish, because something in the description is not 304 2B.

The full grade and finish range we hold is on the stainless steel plate and coil page. Prices there are indicative only. Nickel moves and so does the quote.

What payment terms should you accept?

TermsWho uses itYour exposureWhat to add
30% T/T deposit + 70% before shipmentmost first ordersYou pay the balance before you touch the goodsPre-shipment inspection and photos of the loaded container
100% L/C at sightCorporate buyers, orders above roughly US$100,000Low, if the documents are strictA bank that reads the L/C before the supplier does
30/70 with 70% against B/L copyRepeat buyers after 3 clean shipmentsModerateNothing extra. This is the fair middle
O/A 30-60 daysLong term partners onlyHighest for the seller, so the price carries itCredit insurance, or expect a price premium

The deposit is not greed. A Chinese mill wants payment before it rolls, and stock sizes tie up the trader's own cash. Stock ships 3 to 7 working days after the deposit clears. Mill-roll sizes run 15 to 25 days, and no deposit means no slot in the rolling schedule.

Here is the practical rule I give first-time buyers. Pay 30% up front, hold the balance until a third party has measured the plate and you have seen a photo of the bundles inside the container. That single condition removes most of the argument.

FOB or CIF: which one should you pick?

TermSupplier handlesYou handleWhen it makes sense
FOBDelivery to the vessel at the Chinese portOcean freight, insurance, importYou have a forwarder or want control
CFRFreight to your portInsurance and importSimple orders, single destination
CIFFreight plus minimum insuranceImport clearanceOnly if you check the insurance clause
EXWNothing, goods at the factory doorExport clearance, everything elseRarely correct in China

CIF insurance is usually Institute Cargo Clauses C. That covers a total loss and very little else. Theft, fresh water damage and handling damage are excluded, and those are exactly the three things that happen to a stainless bundle. Ask for ICC A, or keep FOB and insure it yourself for the 0.3% it costs.

Which documents should arrive before you release the balance?

Six documents. If one is missing, the balance waits.

HS codes for flat rolled stainless are 7219.11 to 7219.24 for hot rolled and 7219.31 to 7219.39 for cold rolled, both at 600 mm width and over. Narrow strip under 600 mm moves to 7220. Get the broker to confirm the eight or ten digit code for your market before the container sails. Duty rates have moved several times in the last two years and no supplier's word replaces a customs ruling.

How do you check the plate before it ships?

Thickness

Measure with a micrometer at five points on the first bundle. Cold rolled sheet is supplied to a minus tolerance under ASTM A480 or EN 10088-2, and the allowed minus side is where the money leaks. On thin sheet a 3% minus tolerance is legal and it is still 3% of your material.

Weight

Compare actual bundle weight with theoretical weight at 7.93 kg per square metre per millimetre. A bundle running 3 to 5% under theoretical is inside the standard tolerance. Weigh before you cut, not after.

Grade

201 and 304 look identical when they are wrapped in VCI paper. Positive material identification on three sheets per heat takes ten minutes and settles it. On 316L, ask for the molybdenum reading specifically, because 316 without the L is a common substitution.

Third party inspection

SGS, BV or TUV pre-shipment inspection on a 24 tonne lot costs a few hundred dollars and takes two or three days. On a first order with a new supplier, that is the cheapest insurance in the whole transaction. I recommend it every time a buyer asks me whether to trust a certificate.

What packing survives a 30 to 45 day voyage?

A container crossing four climate zones sweats. Rust on a 2B surface is the number one claim on stainless plate, and it is almost always a packing problem, not a mill problem.

Ask for photos of the packed bundles before they go into the container. Not the loaded container at the end, where you can see nothing. The bundles, banded and wrapped, on the factory floor.

Frequently Asked Questions

How many tonnes of stainless steel plate fit in a 20ft container?

22 to 25 tonnes in practice. The box itself is rated higher, but road limits in the EU and UK usually cap a 20ft at 24 tonnes payload, so the legal limit arrives before the container limit does. A 40ft takes 26 to 28 tonnes.

Is it cheaper per tonne to buy a full container?

Yes, and by a lot. A 20ft loaded to 24 tonnes spreads one ocean freight bill across 24 tonnes. Five tonnes in a shared LCL box pays the same fixed charges plus a per-cubic-metre rate, which often works out two to three times higher per tonne. Below about 10 tonnes it is hard to justify the FCL.

What payment terms are normal for a first order from a Chinese supplier?

30% T/T deposit with 70% before shipment, or 100% L/C at sight for large corporate buyers. The deposit pays the mill, because the mill wants payment before it rolls. Stock sizes ship in 3 to 7 working days after the deposit clears; mill-roll sizes run 15 to 25 days. Every grade and size we quote is listed on the stainless steel plate and coil range.

Which grade should I order for a marine job?

316L is the minimum I would ship for coastal or salt-spray exposure. Where chlorides are concentrated, like deck drains or heat exchanger tubes, duplex 2205 holds up better and costs less than 2507. 304 in a marine environment will pit, usually within 18 months.

Can I put several grades in one container?

Yes, and buyers do it all the time to fill the weight. Each heat still needs its own mill test certificate and its own line on the packing list. Customs will ask which line is which, and so will your own QC when a claim comes up two years later.

What does a mill test certificate have to say?

EN 10204 type 3.1, with the heat number, the chemical composition in actual values rather than ranges, and the mechanical results. If the certificate shows only specification ranges and no measured values, it is a certificate of conformity dressed up as a test report. Reject it.

Related Articles

If you are working through a first container of plate and want a second opinion on the terms or the packing list, send it over. Email [email protected] or use the contact form. We quote 304, 316L, 321, 2205 and 2507 in plate and coil, and I would rather tell you a grade is wrong for your job than sell it to you.

Written by David Chen, Export Manager at FANY LASER. In laser equipment and metal export since 2018, quoting plate, coil and machines for buyers in more than 40 countries. Connect on LinkedIn