November 14, 2026 · Aluminum Alloy
5754 vs 5052 Aluminum Sheet: Are They Interchangeable? (2026)
5754 and 5052 are both aluminium-magnesium sheet, and most buyers treat them as the same metal. They are not. 5754 carries more magnesium (2.6 to 3.6 percent against 2.2 to 2.8), costs roughly USD 110 per tonne more in China, and the temper on the certificate matters more than the alloy number. Pick the wrong temper and you can lose half your yield strength without noticing.
I quote 5754 and 5052 sheet and plate to fabricators in Europe, Southeast Asia and the Gulf every week. The argument is always the same. The drawing says 5754-H111, purchasing finds 5052-H32 at a lower price, the parts bend fine, and then someone runs a load test.
Here is the thing. The alloy choice is the small decision. The temper choice is the one that bites.
Are 5754 and 5052 interchangeable?
Short answer: only when the temper is matched and the application tolerates the difference. They sit in the same 5xxx family, so they look alike, weld alike and machine alike. That is exactly why people assume a straight swap.
Three things break that assumption. Magnesium content is not the same. The temper designations come from different standards, so H111 is not H32. And one of them may not be listed in the pressure vessel code your customer works to.
Get those three straight and 5754 vs 5052 stops being a chemistry argument. It becomes a paperwork question, which is much easier to settle.
What is the difference between 5754 and 5052?
Chemistry first. 5754 is EN AW-5754, old designation AlMg3, defined in EN 573-3. 5052 is UNS A95052 under ASTM B209. The numbers below are the specification limits, not mill averages.
| Element, wt% | 5754 (EN 573-3) | 5052 (ASTM B209) |
|---|---|---|
| Magnesium | 2.6 – 3.6 | 2.2 – 2.8 |
| Manganese | 0.50 max | 0.10 max |
| Chromium | 0.30 max | 0.15 – 0.35 |
| Mn + Cr | 0.10 – 0.60 | not specified |
| Silicon | 0.40 max | 0.25 max |
| Iron | 0.40 max | 0.40 max |
| Copper | 0.10 max | 0.10 max |
| Zinc | 0.20 max | 0.10 max |
More magnesium buys corrosion resistance. That is the whole reason 5754 exists. Above 3 percent magnesium the alloy holds up better in alkaline and mildly acidic service, which is why chemical equipment, tank cars and ship interiors lean towards it.
The manganese and chromium limits do the same job from a different angle. 5754 controls the Mn plus Cr total instead of pinning chromium on its own. Same intent, different route, and the two specs rarely land in the same place.
Silicon is the detail nobody asks about until the anodizing comes back wrong. 5052 caps silicon at 0.25 percent, 5754 allows 0.40. Higher silicon greys the oxide film. For bright anodized work the lower cap helps, and that is one reason 5052 keeps showing up on visible panels.
Physical properties barely move. Density is 2.67 g/cm3 for 5754 and 2.68 for 5052, elastic modulus about 70 GPa on both, thermal conductivity roughly 140 to 160 W/mK on 5754 against 138 on 5052. Nobody has ever lost a job on those numbers.
Is 5754 stronger than 5052?
At the same temper level, a little. The gap is smaller than the temper gap inside either alloy.
| Alloy and temper | Tensile Rm, MPa | Yield Rp0.2, MPa | Elongation |
|---|---|---|---|
| 5754-O / H111 | 190 – 240 | 80 min | 12 – 18% |
| 5754-H22 / H24 | 220 – 270 | 130 min | 8 – 11% |
| 5052-O | 170 – 215 | 65 min | 18% min |
| 5052-H32 | 215 min, 228 typical | 160 min, 193 typical | 12% typical |
| 5052-H34 | 240 – 275 | 180 min | 8 – 10% |
Read the table down, not across. 5754-H111 gives you 80 MPa yield. 5052-H32 gives you 160. That is double, and both sheets look identical in the rack.
Read it across instead and 5754 wins by a nose at matched temper. 220 to 270 MPa tensile against a 215 MPa ASTM minimum. Nothing you would redesign a part around.
One caution on the numbers. Mechanical minimums in EN 485-2 and ASTM B209 are set per thickness band, so a 0.8 mm sheet and a 6 mm plate do not carry the same limits. Quote the thickness when you quote the temper, and read the mill certificate against the right band.
Which temper should you order, H111 or H32?
This is where most substitution mistakes start. H111 and H32 are not translations of each other.
H111 means annealed and then slightly work-hardened by stretching or levelling. It is barely above O temper. H32 means strain-hardened to a quarter hard and then stabilised against room-temperature ageing. Different process, different strength, roughly double the yield.
So when a European drawing says 5754-H111 and purchasing ships 5052-H32, the part gets stronger and less formable. Bend radii open up, springback changes, and tight draws start to crack. When it goes the other way, the part gets soft and fails under load.
My rule is blunt. Never accept a temper substitution on a formed or loaded part without a drawing review. On a non-structural cover panel, do what you like.
Which alloy should you actually use?
| Application | Usual choice | Why |
|---|---|---|
| Automotive inner panels, body structure | 5754-H22 / H24 | European OEM drawings call it, formability and corrosion both matter |
| Ship superstructure, interiors, lockers | 5754 | Extra magnesium for salt service, easier to form than 5083 |
| Hull plate in continuous seawater | 5083 | 4.0 to 4.9% magnesium, the yard standard |
| Tanks, enclosures, HVAC, general sheet metal | 5052-H32 | Cheaper, weldable, plenty strong for the job |
| Pressure vessels to a code | 5052 | Listed in ASME SB-209, 5754 usually is not |
| Bright anodized visible panels | 5052 | Lower silicon cap gives a cleaner film |
The pressure vessel line is worth a second look. If the vessel has to be stamped, the alloy has to be in the code the inspector works to. ASME SB-209 covers 5052. 5754 is not in the common listing, so a coded job usually stays on 5052 no matter what the drawing says. Check the code before you check the price. Both grades sit in our aluminum sheet and plate range, and the offer states the standard and the temper on its face.
What does 5754 cost compared with 5052?
5754 runs a premium, and it is a small one. On the Changjiang spot market for 7 August 2026, 5052 plate averaged CNY 27,370 per tonne and 5754 plate averaged CNY 28,170. That is a spread of CNY 800 per tonne, about USD 110 at 7.15.
The base metal has moved since. SMM put the A00 ingot at CNY 23,110 per tonne on 13 November 2026, with LME cash aluminium at USD 3,155 per tonne and exchange stocks at 226,350 tonnes. November plate prices follow that, so treat the August spread as a ratio rather than a quote.
Automotive grades carry their own premium on top. AluSeek listed 5754 automotive body structure strip at CNY 26,500 to 27,500 per tonne on 13 November 2026, averaging 27,000, while 5754 automotive inner panel ran CNY 30,900 to 33,100, averaging 32,000. Same alloy, different surface and tolerance package, nearly CNY 5,000 apart.
That last line matters more than the alloy spread. When two quotes for 5754 differ by 20 percent, look at the temper, the thickness tolerance and whether the surface is mill finish or brushed before you assume somebody is cheating.
If you are holding two quotes for the same part, send both to me with the standard and the temper. I will tell you which line is short. The team answers through the contact page.
How do you stop a substitution on the purchase order?
Five lines do most of the work:
- Write the standard, not just the number. EN AW-5754 to EN 573-3, or UNS A95754 to ASTM B209. A bare 5754 is an invitation.
- Write the temper in full and add no substitution without written approval. H111, H22, H24, H32, H34.
- Name the mechanical standard and the thickness band, so the mill certificate can be checked against the right minimums.
- Ask for the mill certificate with the heat number and the actual magnesium content before the container leaves.
- If dual certification is offered, check the chemistry fits both windows. It only works when magnesium lands between 2.6 and 2.8 and the chromium and manganese lines satisfy both specs.
That fifth point is real and it is also where people get lazy. A mill can legitimately certify one heat to both 5052 and 5754 when the chemistry falls in the overlap. That is fine if you asked for it. It is not fine when it is used to paper over a temper you did not order.
Frequently Asked Questions
Are 5754 and 5052 aluminum sheet interchangeable?
Only when the temper matches and the application tolerates the difference. Both are aluminium-magnesium sheet, both are non-heat-treatable and both weld with 5356 filler. But 5754 carries more magnesium and its common European tempers (H111, H22) do not line up with 5052-H32. Swap 5052-H32 for 5754-H111 and the yield strength drops from 160 MPa to 80 MPa.
Is 5754 stronger than 5052?
At the same temper level, slightly. 5754-H22 runs 220 to 270 MPa tensile against 215 MPa as the ASTM minimum for 5052-H32. The alloy is not where the difference lives, though. Temper decides strength. 5754-O at 190 to 240 MPa is weaker than 5052-H34 at 240 to 275 MPa.
What is 5754 aluminum called in other standards?
EN AW-5754, old designation AlMg3, under EN 573-3 for chemistry and EN 485-2 for mechanical properties. In ASTM it is UNS A95754, listed in B209 for sheet and plate. 5052 is UNS A95052, also under ASTM B209. Same family, different national standards.
Can you weld 5754 to 5052?
Yes. Both are 5xxx alloys, both are non-heat-treatable, and 5356 filler works on either. You lose a little strength in the heat-affected zone on both, and neither needs post-weld heat treatment. Match the filler to the higher-magnesium side and you are fine. Our aluminum sheet and plate range covers both grades.
Which is better for marine work, 5754 or 5052?
5754, because of the higher magnesium. For hull plate and anything in continuous seawater, most yards go to 5083 at 4.0 to 4.9 percent magnesium instead. 5052 is the sensible choice for superstructure, lockers and interior panels where weight and cost matter more than peak strength.
Related Articles
- 5052 vs 6061 vs 7075: Which Aluminum Grade Fits the Job
- 5083 Aluminum Plate Price 2026: Marine Grade Cost per Kg from China
- Aluminum Temper Designations: O, H and T Explained for Buyers
- Aluminum Sheet Weight and Price per kg: How to Check a Quotation (2026)
- Aluminum Sheet Thickness Tolerance: GB/T 3880.3 vs ASTM B209 (2026)
- Laser Industry News November 16 2026: Machine Tools Up 19%, US 232 Derivative List, SANY AI Welding, Steel Down 5.1%
Sources: EN 573-3 chemical composition and EN 485-2 mechanical properties for EN AW-5754 / AlMg3, including magnesium 2.6 to 3.6%, manganese 0.50 max, Mn+Cr 0.10 to 0.60, density 2.67 g/cm3, elastic modulus 70.5 GPa, thermal conductivity 140 to 160 W/mK, and H111 limits of 190 to 240 MPa tensile, 80 MPa yield and 12 to 18% elongation by thickness band (BIKAR-METALLE GmbH alloy data sheet); ASTM B209 chemistry and mechanical minimums for 5052 / UNS A95052, including magnesium 2.2 to 2.8%, chromium 0.15 to 0.35%, silicon 0.25 max, density 2.68 g/cm3 and H32 values around 228 MPa tensile and 193 MPa yield typical (VTECH Materials technical data sheet TDS-AL-5052-H32-B209 Rev A, April 2026, and Direct Aluminum 5052-H32 B209 sheet data). Price data: Changjiang nonferrous spot table for 7 August 2026 with 5052 plate averaging CNY 27,370 per tonne and 5754 plate averaging CNY 28,170 per tonne; AluSeek aluminium price board updated 13 November 2026 with 5754 automotive body structure strip at CNY 26,500 to 27,500 and 5754 automotive inner panel at CNY 30,900 to 33,100 per tonne; SMM A00 ingot at CNY 23,110 per tonne and LME cash aluminium at USD 3,155 per tonne with 226,350 tonnes of exchange stocks, 13 November 2026 (Yieh Corp LME and SMM table). Every figure should be confirmed on the day of quotation.
