November 9, 2026 · Aluminum Alloy

Anodized Aluminum Sheet: AA10 to AA25, Alloy Choice and What to Check (2026)

Anodizing puts 5 to 25 microns of oxide on the surface of an aluminum sheet, and that number decides how the part looks after five years outdoors. ISO 7599:2018 grades the coating AA5 to AA25 by minimum average thickness. Below is how the grades work, which alloys anodize clean, and what to put in the purchase order so the container matches the sample.

I quote anodized aluminum sheet and plate to window fabricators, panel shops and machine builders almost every week. The question that comes back most is short. My other supplier quoted 15 microns for less money, what am I missing?

Usually one of three things. A lower thickness class behind the same label. A cheaper alloy under the same finish. Or a coating that was never sealed properly. None of those show up in a photo.

What does AA15 mean on an anodized aluminum sheet?

ISO 7599:2018 writes the coating as a thickness class. The class is AA plus the minimum average thickness in microns. AA15 means 15 microns average, and the worst local reading on the sheet cannot drop below 12.

Class Min average Min local Where it usually goes
AA55 µm4 µmIndoor trim, low wear
AA1010 µm8 µmInterior panels, light handling
AA1515 µm12 µmExterior windows, general architectural
AA2020 µm16 µmCoastal, industrial, dark dyes
AA2525 µm20 µmHeavy exterior, salt or pollution

One rule sits under that table. The minimum local thickness can never fall below 80 percent of the minimum average. So AA15 gives you 12 microns at the worst point, not 15 everywhere.

How the plant measures matters just as much. The usual method is eddy current under ISO 2360. In a dispute the referee method is a micro-section under ISO 1463 or ISO 9220. Both say no reading within 5 mm of a contact mark or a sharp edge, because the coating builds differently there.

Europe buys to Qualanod. The current Qualanod specification took effect on 1 January 2026 and follows ISO 7599, with ISO 10074 covering hard anodizing. If your customer names Qualanod, ask the plant for its licence number before you send a price.

Which aluminum grade should you anodize?

Not every alloy anodizes the same colour, even on the same line. The alloy sets the tone before any dye goes in.

Alloy Anodizing response Typical use
5005Clear silver, grey or brownishGeneral architectural sheet and plate
5052Clear and even at normal thickness, yellowish when the coating runs thickTruck panels, structural parts
6063Excellent, clear silverExtrusions, trim, profiles
6061Clear and even; the shop favourite for hard anodizingMachined parts, structural sheet
6082Close to 6061, slightly less brightStructural parts for EU projects
7075Grey, blue-grey or mottled brown-blackHidden parts only
2024Darker and less uniform because of the copperHidden parts only

Two rules come out of this. Keep one alloy per visible assembly, because a 6061 bracket next to a 6063 frame will not match after dyeing. And if the part is decorative, do not let anyone talk you into 2024 or 7075 to save weight.

High-silicon castings are their own problem. The silicon does not anodize, so the surface comes out grey and powdery. That is a casting issue, not something the anodizing line can fix.

How thick should the coating be for your application?

Indoors, AA10 is enough. Most interior trim and light panels sit at 10 microns and last for years.

Outdoor is where the arguments start. In my experience, window fabricators in Southeast Asia order AA15 as standard. Gulf projects and anything within a few kilometres of the coast go to AA20 or AA25.

Dark dyes need more. ISO 7599 notes that some dyestuffs need class AA20 or higher to absorb properly and hold their light fastness. Black and bronze are the usual cases.

Hard anodizing is a different product. It is specified under ISO 10074 at 25 to 50 microns and it is not decorative. Do not accept a hard anodizing quote when you asked for decorative, and do not expect a decorative price for hard.

Does anodizing change the sheet thickness?

Yes, slightly, and the direction surprises people. About half of the coating grows outward and half grows into the metal.

A 20 micron coating adds roughly 10 microns per surface. On both faces that is about 0.02 mm on the sheet.

That matters when you buy anodized sheet at plus or minus 0.02 mm on thickness, which is what Chinese mills quote on 6061 and 5052. Say whether the tolerance applies before or after coating.

Cut edges and punched holes are the other spot. Coating builds on an edge, so deburr before anodizing if the parts have to fit together.

What should be in the anodized sheet purchase order?

Seven lines stop most of the trouble I see:

  1. Alloy and temper, for example 5052-H32 or 6061-T6. Not just aluminum sheet.
  2. Size, thickness and the tolerance band, plus whether it applies before or after coating.
  3. Thickness class written as the ISO 7599 class, AA15 or AA20.
  4. Finish: clear, or a dye colour with a sample or RAL reference.
  5. Sealing to ISO 7599 clause 7, with the ISO 3210 acid dissolution test if you need a number.
  6. Appearance limits: no contact marks on the visible face, no die lines, no shade difference between sheets in one lot.
  7. Test report and protection: coating thickness readings, sealing result, PVC film or interleaved paper, seaworthy packing.

Most complaints I handle come from line six. The coating itself was fine, but the sheets were dyed in two batches and the client saw the seam on the wall.

How do you check anodizing when the container arrives?

Buy a coating thickness gauge before the second container. An eddy current gauge costs less than one rejected facade panel.

Take five readings per sheet across the face. Stay 5 mm away from edges and contact marks, then compare the average against the class you ordered. AA15 fails the moment a reading drops under 12 microns.

If you paid for sealing, ask for the ISO 3210 result. A white chalky bloom that rubs off is a sealing failure, and outdoors it shows up within one season.

Check colour against the approved sample, not from memory. Keep one sheet from the first lot in the office. Dark streaks and patchy areas usually point at alloy segregation rather than the anodizing line, which is why the alloy call comes before the price call.

What does anodizing add to the price?

Start with the metal. SMM put the A00 aluminum spot at RMB 23,260 to 23,810 per tonne through October 2026, averaging about RMB 23,596 per tonne. That is roughly USD 3.30 per kg at 7.15.

Mill finish 5052-H32 plate in 3 to 50 mm quoted at USD 3.60 to 4.40 per kg ex-works China in the same month. Anodizing or powder coating adds about USD 0.30 to 0.60 per kg, and it adds process time.

Chinese factory listings for anodized 6061 and 5052 sheet sit at USD 3,600 to 3,900 per tonne, with a 3 tonne minimum and 7 to 20 working days.

Ask whether the plant charges per tonne or per square metre. Thin sheet is usually quoted per tonne, and the same micron costs more per kilo there, so a 0.8 mm sheet can look expensive next to a 3 mm plate for no good reason.

If you are holding two quotes for anodized aluminum sheet, send both to me with the class and the alloy. I will tell you which line is short. The team answers through the contact page.

Frequently Asked Questions

What does AA15 mean on anodized aluminum sheet?

AA15 is the ISO 7599 thickness class. It means 15 microns minimum average coating, and no single reading below 12 microns. It is the common class for exterior window and facade work.

Which aluminum alloy is best for anodizing?

For sheet and plate, 5005, 5052, 6061 and 6063 give the cleanest result. 6061 is the machine shop favourite and takes hard anodizing well. 2024 and 7075 come out darker and mottled, so keep them for hidden parts. Our aluminum alloy range covers these grades.

How thick should anodizing be for outdoor use?

AA15 is the practical minimum for exterior work. Coastal, industrial or heavily polluted sites should go to AA20 or AA25. Black and bronze dyes often need AA20 to hold colour.

Does anodizing change the sheet thickness?

Yes, by about half the coating thickness per surface. A 20 micron coating adds roughly 10 microns per side, about 0.02 mm across the sheet. Tell the mill whether your tolerance is before or after coating.

Can I get anodized aluminum sheet with a coating thickness report?

Yes. We ship the mill certificate for the alloy plus eddy current thickness readings per sheet, and the ISO 3210 sealing result when it is specified. Standard sizes and tempers are listed on the aluminum sheet and plate page, or send the drawing through our contact form.

Related Articles

Written by David Chen, Sales Engineer at FANY LASER. Connect on LinkedIn for aluminum and stainless sourcing, price data and market updates.

Sources: ISO 7599:2018, Anodizing of aluminium and its alloys, Table 1 coating thickness classes AA5 to AA25, clause 6.2 classification, clause 6.3 thickness measurement by ISO 2360 with micro-section as referee method, and clause 7 quality of sealing; Qualanod Specifications for the sulfuric acid based anodizing of aluminium, edition 01.01.2026, effective 1 January 2026, aligned with ISO 7599 and ISO 10074; Aluminum Anodizers Council alloy and temper guidance, including 5052 yellowing at thicker coatings, 6063 and 6463 clear silver, and 7xxx grey to mottled brown-black; NORAMARK anodizing process notes, Type II coating 8 to 25 microns held to about plus or minus 5 microns, roughly half of the coating growing outward, and 2024 or 7075 reading darker and less uniform than 6061, 6063 and 5052; GNEE 5052 and 5083 aluminum plate price report dated 21 October 2026, with the SMM A00 spot at RMB 23,260 to 23,810 per tonne, month to date average near RMB 23,596 per tonne, about USD 3.30 per kg at an indicative 7.15, and surface treatment adding roughly USD 0.30 to 0.60 per kg; a Chinese factory listing for anodized 6061 and 5052 sheet at USD 3,600 to 3,900 per tonne, 3 tonne minimum, 7 to 20 working days and plus or minus 0.02 mm thickness tolerance. Every figure should be confirmed on the day of quotation.