November 15, 2026 · Laser Cutting
Fiber Laser Cutting Copper and Brass: Power, Gas and Settings
Bare copper reflects 94–96% of a 1,070 nm fiber laser beam. Only 4–6% of your power enters the metal. Brass is more forgiving at 90–93% reflection, which is why the same machine cuts 20 mm brass and stops at 8 mm copper. If you are quoting fiber laser cutting copper without knowing that gap, you will quote the wrong machine.
Most fiber laser cutting copper questions I get start with the wrong number: watts. I sell cutting machines to job shops and busbar manufacturers. The copper jobs that come back with complaints are almost never a machine failure. They are a power choice, a gas choice, or a source that was never rated for reflective metal.
Why Copper Is the Hardest Common Metal for a Fiber Laser
Three properties work against you at the same time. High reflectivity means most of the beam bounces off before it can melt anything. High thermal conductivity pulls heat away from the kerf as fast as you put it in — copper conducts roughly three times better than brass. And a low melting point for a metal of that conductivity means the sheet can sag before the cut is clean.
| Metal | Reflectivity at 1,070 nm | Absorptivity | Power density to open a keyhole |
|---|---|---|---|
| Copper C110 | 94–96% | 4–6% | 1.0 × 108 W/cm² |
| Cartridge brass Cu-30Zn | 90–93% | 7–10% | 5 × 107 W/cm² |
| Stainless 304 (for scale) | about 60–70% | 30–40% | lower than both |
The reflectivity figures are from a September 2026 process study published by Yihai Lasers. The practical reading is simple: copper needs about twice the power density that brass needs before a cut even starts.
Brass has one hidden advantage. It contains zinc, which boils at 907 °C, well below the melting range of the copper alloy. That zinc vapour helps blow molten metal out of the kerf. Pure copper has no such helper, so the melt stays where it is and turns into dross.
How Much Power Do You Actually Need?
A published parameter reference from SBMachines (April 2026) lists the thickest sheet each power level can cut in production mode. Copper and brass are far apart at every level.
| Laser power | Max brass | Max copper | Typical job |
|---|---|---|---|
| 2 kW | 6 mm | 3 mm | Thin busbar, trim, signage |
| 3 kW | 6 mm | 4 mm | Connector blanks, 3 mm copper |
| 6 kW | 20 mm | 8 mm | Busbar production, mixed shop |
| 12 kW | 16 mm | 10 mm | Thick copper, high throughput |
| 20 kW | 20 mm | 12 mm | Heavy sections, trial parameters |
Two things stand out. There is a hard floor at 2 kW — below that, no listed mode cuts copper at all. And the brass column is not monotonic: 6 kW handles 20 mm brass, while the 12 kW row shows 16 mm because the gas, nozzle and speed change with the power class. Do not compare rows as if they were a straight line.
My rule for buyers: if copper is more than a sideline, start at 6 kW. A 3 kW machine will cut 4 mm copper all day, but the moment a customer sends 6 mm busbar you are turning work away. The price difference between 3 kW and 6 kW on a fiber laser cutting machine is far smaller than the cost of a machine that cannot take the order.
The 50% Rule: Copper Versus Brass at the Same Power
Yihai's 2026 benchmark matrix, measured on production machines with high-pressure nitrogen, gives real cutting speeds for brass in metres per minute. The copper column is not shown because it is not the same shape — for pure copper C11000, the practical thickness limit at any given power is roughly half the brass value.
| Power | 1 mm | 2 mm | 3 mm | 4 mm | 6 mm | 10 mm |
|---|---|---|---|---|---|---|
| 2 kW | 15–30 | 8–11 | 3–4.5 | 2–2.3 | 0.6–0.8 | — |
| 4 kW | 30–35 | 15–18 | 8–12 | 3.5–4.5 | 2–2.5 | 0.4–0.6 |
| 6 kW | 35–45 | 20–26 | 12–15 | 9–10 | 3.5–4.5 | 1.2–1.5 |
| 12 kW | 45–50 | 35–43 | 22–26 | 18–24 | 9–11 | 4.5–5.5 |
| 20 kW | 45–55 | 40–50 | 28–35 | 25–30 | 19–22 | 10–13 |
Speeds are brass in m/min. Above 4 mm the numbers fall off a cliff, and that is where buyers get surprised. A 2 kW machine cutting 6 mm brass runs at 0.6–0.8 m/min, which is slow enough that a 30-part order takes the whole afternoon.
Assist Gas: Oxygen for Copper, Nitrogen for Brass
This is where fiber laser cutting copper and brass part company. The two metals genuinely want different gases, and the wrong one costs you either edge quality or a lens.
For copper, use oxygen. The copper–oxygen reaction is exothermic and the cupric oxide layer that forms absorbs 1,070 nm energy better than bare metal does. That raises coupling efficiency and lets you cut thicker sections at lower power. The trade-off is an oxidised edge that has to be machined or pickled afterwards.
For brass — especially electrical busbar and connector work — use high-pressure nitrogen. At 18–25 bar and 99.999% purity you get an oxide-free, dross-free edge that needs no post-processing. Low pressure is the reason brass cuts come out with dross; the melt is more viscous than steel and needs gas momentum to clear the kerf.
| Gas | Pressure | Purity | Best for | Edge result |
|---|---|---|---|---|
| Nitrogen | 18–25 bar | ≥99.999% | Brass busbar, connectors, cosmetic parts | Oxide-free, dross-free |
| Oxygen | 1–3 bar | ≥99.5% | Copper thicker than 5 mm | Oxidised, needs pickling |
| Compressed air | 16–20 bar | uncontrolled | Not recommended on copper | Verdigris, lens clouding |
One warning about shop air, because everybody tries it to save gas money. On copper alloys, air leaves green verdigris on the cut edge and a clouding film on the protective lens. The lens damage is cumulative. Yihai's field data puts protective lens life at 60–80% lower than with nitrogen. A €15 lens every few weeks costs more than the gas you saved.
Back-Reflection Protection Is a Machine Requirement, Not an Option
With 94–96% of the beam bouncing off cold copper, some of it travels back up the optical path. That energy lands on the protective window, the collimating lens and eventually the delivery fibre. This is how reflective-metal jobs kill sources.
Good machines deal with it in three layers, and Coherent's 2026 datasheet for its HighLight FL industrial source is a clear public example: a multi-stage back-reflection immunity system, so the source is rated for brass, copper and aluminium. The cutting head adds a photodiode that watches returning light and shuts the laser off within 1 ms if reflected power exceeds roughly 5–10% of forward power, plus a water-cooled beam dump between the protective window and the collimator to absorb what the diode does not catch.
Ask your supplier three questions before you sign. Does the laser source carry back-reflection protection, and for which materials is it rated? Does the cutting head have a beam dump? What is the spare price and lead time on protective windows? A supplier who cannot answer the first one in writing is selling you a machine that will cut steel forever and copper until it does not.
Starting Settings by Thickness
These are starting points for a 3 kW and a 6 kW machine on 1.5–3 mm copper and brass. Every machine, lens and gas supply differs, so cut a 100 mm sample before you run the job.
| Material and thickness | Power | Gas and pressure | Starting speed | Watch for |
|---|---|---|---|---|
| Brass 1 mm | 2 kW | N2 20 bar | 15–30 m/min | Burr on the exit side |
| Brass 3 mm | 3 kW | N2 20 bar | 12–15 m/min | Dross at low pressure |
| Copper 2 mm | 3 kW | O2 2–3 bar | 4–6 m/min | Oxide film, heat distortion |
| Copper 4 mm | 6 kW | O2 2–3 bar | 3.5–4.5 m/min | Dross, taper on thick corners |
| Copper 6 mm | 6 kW | O2 2–3 bar | 2–2.5 m/min | Bottom dross, lens heating |
| Copper 8 mm | 6–12 kW | O2 2–3 bar | 1.2–1.5 m/min | Edge squareness, test cut first |
Focus position is the setting to leave alone until the sample cut tells you otherwise. On copper it usually sits near or just below the surface, but the exact number depends on the lens, the nozzle and the gas. Change one variable at a time, or you will spend a day chasing your own adjustment.
What Copper Capability Adds to the Machine Price
Public asking prices for standard 3015 and 4020 machines in late 2026: a 3 kW runs $26,000–36,000 FOB China, a 6 kW with an exchange table runs $42,000–58,000, and 12–15 kW sits at $75,000–110,000 and up. These are listing prices, not quotes.
The copper-relevant part of the price is not the wattage. It is the source model (a source with back-reflection protection costs more than a basic one), the cutting head with a beam dump, and the gas system. If you plan to run brass busbar with nitrogen, add a nitrogen generator or a high-pressure bundle — on a machine cutting reflective metal every day, gas is the largest running cost, not electricity.
Payback is quick when the copper work is steady. Busbar, switchgear parts, heat sinks and connector blanks are usually small, high-value parts cut from sheet, and a fiber laser replaces milling, punching and secondary finishing on a lot of them. The jobs that do not pay back are the ones where you bought 3 kW and keep quoting 8 mm copper.
Five Questions to Ask Before You Buy
- What is the thickest copper your machine cuts in production, not in a demo? Ask for a video of your thickness, your gas, your part.
- Is the laser source rated for reflective metal? Get the model and the datasheet line that says so.
- Does the head have a beam dump and a back-reflection interlock? Both, not one.
- Which gas do you recommend for my parts, at what pressure and purity? A supplier who says "air works fine" has not cut much copper.
- What does a protective window cost, and how many do you ship with the machine? Reflective metal eats windows.
Send your material list, thickness range and monthly volume and you get a configuration with a real price, not a range. Our machine specs and configurations are on the fiber laser cutting machine page, and you can send drawings through the contact form.
Frequently Asked Questions
Can you cut copper with a fiber laser?
Yes, from about 2 kW upward. A 2 kW machine cuts 3 mm copper, 3 kW cuts 4 mm, 6 kW cuts 8 mm and 12 kW cuts 10 mm, per SBMachines' April 2026 parameter reference. Below 2 kW, most published tables list no copper mode at all. The catch is speed and edge quality, not whether it cuts.
Should I use nitrogen or oxygen for copper?
Oxygen for copper, nitrogen for brass. The oxygen reaction with copper is exothermic and the oxide layer absorbs the beam better, which is why 1–3 bar oxygen cuts thicker copper at lower power. Nitrogen at 18–25 bar and 99.999% purity gives an oxide-free edge on brass busbar. Compressed air is not recommended on copper — it leaves verdigris and clouds the protective lens.
Why does my copper cut have dross?
Usually three causes, in this order: gas pressure too low for the melt viscosity, focus too high, and power too low for the thickness. Copper conducts heat away roughly three times faster than brass, so the kerf cools before the molten metal clears. Raise pressure first, then check focus on a sample, then step up power.
Can copper damage my laser source?
It can, if the source is not rated for reflective material. Copper reflects 94–96% of a 1,070 nm beam, and the returning light heats the protective window, the collimating lens and the delivery fibre. Machines built for it use a back-reflection interlock that cuts the laser within 1 ms plus a beam dump in the head. Ask for both before buying.
How fast can I cut 3 mm brass?
On a 3 kW machine with high-pressure nitrogen, 12–15 m/min is the published range, and 2 kW manages 3–4.5 m/min on the same thickness. Pure copper at 3 mm is slower — plan on roughly half the brass speed for the same power.
Do I need a different machine for copper and steel?
No. One fiber laser cuts both, but the settings, gas and nozzle change, and the source must be rated for reflective metal. The practical requirement is power: if copper is a real part of your work, buy 6 kW rather than 3 kW, because 3 kW tops out at 4 mm copper. Power options and configurations are listed on the fiber laser cutting machine page.
Sources
Reflectivity, absorptivity and keyhole power density at 1,070 nm: Yihai Lasers process study, August 2026. Brass cutting speeds and the copper-to-brass 50% thickness rule: Yihai Lasers benchmark matrix, September 2026. Maximum thickness by power for brass and copper: SBMachines fiber laser cutting parameter reference, April 2026. Back-reflection protection design and 1,070 nm source rating: Coherent HighLight FL Compact datasheet, 2026. Machine price bands: public supplier listings, October 2026.
Related Articles
- Fiber Laser Cutting Machine Price 2026: 3 kW, 6 kW and 12 kW FOB China
- Assist Gas Compared: Nitrogen, Oxygen and Compressed Air
- Laser Cutting Defects: Dross, Burrs and Taper Fixes
- Laser Cutting Tolerance and Kerf: ISO 2768 Guide
- Fiber Laser Power Selection: 1500 W, 3000 W or 6000 W
- Laser Industry News November 16 2026: Machine Tools Up 19%, US 232 Derivative List, SANY AI Welding, Steel Down 5.1%
